Carnivore2 announcements

ページ 11/15
4 | 5 | 6 | 7 | 8 | 9 | 10 | | 12 | 13 | 14 | 15

By raymond

Hero (600)

raymond さんの画像

27-12-2021, 19:26

Alexey wrote:

Sadly, I had almost no feedback from Carnivore2 users and manufacturers about testing the upcoming version with a few nice new features and important bugfixes. This is a serious demotivator...

How safe is it to put it in? As I do want to have fixes and new functions, however I do not want to end up with a bricked device and loose data :-)

By raymond

Hero (600)

raymond さんの画像

27-12-2021, 19:30

I have read the release note. I will install it tomorrow and start using it. If you hear nothing it means it goes well :-)

By Manuel

Ascended (18792)

Manuel さんの画像

27-12-2021, 21:08

I also have no USB blaster, so I didn't test the new FPGA code. I hope that you want to upgrade it on the MSX fair. Also, I saw that in last MSX fair in October, the Carnivore 2 didn't work properly on my expanded 8250. (It may have been a Nextor thing, though.) It didn't want to map the first partition to drive A:, so no boot.But it worked fine in my turboR, both times the cart was in slot 1.

By sdsnatcher73

Prophet (3237)

sdsnatcher73 さんの画像

27-12-2021, 21:43

raymond wrote:

I have read the release note. I will install it tomorrow and start using it. If you hear nothing it means it goes well :-)

Don’t take this the wrong way, it is not an attack against you in any way. Truly. I just quoted your post to help make a general remark.

I think one thing Alexey might be saying is do tell him if it is working well. Feedback does not have to only be given if something isn’t working…

By raymond

Hero (600)

raymond さんの画像

28-12-2021, 07:25

Manuel wrote:

I also have no USB blaster, so I didn't test the new FPGA code. I hope that you want to upgrade it on the MSX fair. Also, I saw that in last MSX fair in October, the Carnivore 2 didn't work properly on my expanded 8250. (It may have been a Nextor thing, though.) It didn't want to map the first partition to drive A:, so no boot.But it worked fine in my turboR, both times the cart was in slot 1.

I do have a USB blaster, but there is no carnivore2.pof in "Carnivore2_v250_BetaTesting_003.zip". Where can I find this pof file?

By Alexey

Guardian (3385)

Alexey さんの画像

28-12-2021, 11:29

raymond wrote:
Manuel wrote:

I also have no USB blaster, so I didn't test the new FPGA code. I hope that you want to upgrade it on the MSX fair. Also, I saw that in last MSX fair in October, the Carnivore 2 didn't work properly on my expanded 8250. (It may have been a Nextor thing, though.) It didn't want to map the first partition to drive A:, so no boot.But it worked fine in my turboR, both times the cart was in slot 1.

I do have a USB blaster, but there is no carnivore2.pof in "Carnivore2_v250_BetaTesting_003.zip". Where can I find this pof file?

All files except Boot Menu can be found here:
https://rbsc.su/files/Carnivore2_v250_BetaTesting_001.zip

By raymond

Hero (600)

raymond さんの画像

28-12-2021, 18:30

Alexey wrote:

All files except Boot Menu can be found here:
https://rbsc.su/files/Carnivore2_v250_BetaTesting_001.zip

OK, thanks. I got all the necessary files.

Updating of the FPGA code will take a bit longer... There is no JTAG connector on the board. The holes are there, but no connector. I have to order a connector to solder it in :)

By GreyWolf

Champion (410)

GreyWolf さんの画像

28-12-2021, 18:50

raymond wrote:
Alexey wrote:

All files except Boot Menu can be found here:
https://rbsc.su/files/Carnivore2_v250_BetaTesting_001.zip

OK, thanks. I got all the necessary files.

Updating of the FPGA code will take a bit longer... There is no JTAG connector on the board. The holes are there, but no connector. I have to order a connector to solder it in :)

See this description with photos :)

By Pencioner

Scribe (1523)

Pencioner さんの画像

28-12-2021, 20:00

raymond wrote:

Updating of the FPGA code will take a bit longer... There is no JTAG connector on the board. The holes are there, but no connector. I have to order a connector to solder it in Smile

soldered connector likely to make the problem closing the cartridge case afterwards... connectors are higher than available space between pcb and case. i tried once, and then i had to cut off the connector pins a little bit to shorten them (i was lucky to solder male connector so it was an option) and as a result the connectivity to the cable was even worse than if you push and keep it by hand

By raymond

Hero (600)

raymond さんの画像

29-12-2021, 07:29

GreyWolf wrote:
raymond wrote:

OK, thanks. I got all the necessary files.

Updating of the FPGA code will take a bit longer... There is no JTAG connector on the board. The holes are there, but no connector. I have to order a connector to solder it in Smile

See this description with photos :)

Ah, thanks. I only have to make a USB cable now :)

ページ 11/15
4 | 5 | 6 | 7 | 8 | 9 | 10 | | 12 | 13 | 14 | 15