Search results
Chinon FZ-357 Floppy Drive " Not Ready" on AX-370
Score: 157.71 %,
Type: Forum topic , Comments: 5 comments
DS0
- MM
-TTL/C-MOS
By default it also had a jumper set for the RDY signal, which I had ...
Which jumpers are set? For my Chinon FZ-354 I had to set the following jumpers:
- DS0
- MM ... had to set the following jumpers:
- DS0
- MM
-TTL/C-MOS
By default it also had a jumper ...
Resistors, Capacitors and Inductor values of SANYO WAVY 70FD
Score: 157.94 %,
Type: Forum topic , Comments: 3 comments
Does anyone know the values of the following resistors, capacitors and inductors from SANYO WAVY 70FD? Or at least can measure them for me from their machine.
I put the resistor numbers in order according to the proximity of each others
Just ...
AX-370 Black Screen with RTC ROM
Score: 158.55 %,
Type: Forum topic , Comments: 11 comments
Recently, I had black screen upon turning on my Sakhar AX-370. I troubleshooted it and I can verify the following:
- Turns on and run all the way normally using CBIOS ROM without any problem
- Turns on and run all the way normally using MSX1 ROM ...
Sanyo Wavy 70FD, L105 inductor picture or value NEEDED
Score: 158.76 %,
Type: Forum topic , Comments: 11 comments
Can someone who owns this machine tell me what is the value of the inductor at L105? A clear picture of the inductor will also help.
I hope someone is willing to help.
I can make a photo when I get I can make a photo when I get back home ...
This is how to change RAM slots assignment on Sanyo AX-370 and 70FD
Score: 159.27 %,
Type: Forum topic , Comments: 2 comments
On the AX370, the RAM is assigned to slot 3-3, if one would like to change it to slot 3-0 (just ... that you will move the RAMS from slot 3-3 to 3-0.
R112 (10K Ohm) is for Slot 3-3
R236 (10K Ohm) is for Slot 3-0
I don't if that is helpful or not, but for me it was since I want to slot 3-3 ...
Sanyo 512KB PCB on AX-370 Issue
Score: 157.93 %,
Type: Forum topic , Comments: 9 comments
I got the board and built it up. I connected all the 4 chips to the 4 slots that are available on the MSX PCB but I am not sure if that's the right way to go since there was not a lot of instruction on the gerber file except about the A8 (pin 47 on ...
FMPAC has stopped working on my Carnivore2
Score: 160.32 %,
Type: Forum topic , Comments: 8 comments
I was trying to play some FM files and I got an error syntax at line 10. Tried. I will try to update it later, it may fix that issue when installing the new file. But, any recommendation is welcome.
Maybe your flash chip has Maybe your flash ...
SFG Cartridge by RBCS Parts Question
Score: 159.71 %,
Type: Forum topic , Comments: 12 comments
I am building the SFG cartridge created by RBCS, There is capacitor value C20 after the amplifier AU1. The value is 0.027uf (27nf) I wonder what will be the next value that will be better to replace that since the 27nf SMD is not easy to find for me. I can get 33nf or 22nf. Is the lower capacitor ...
Will Sega 315-5560 chip work instead of YMF278B-F for Wozblaster?
Score: 160.97 %,
Type: Forum topic , Comments: 7 comments
I am trying to build Wozblaster, but I can not locate any of YMF278B-F chip, but I managed to locate original Sega 315-5560 chip instead. I know that chip is strip down of the YMF278B-F but will it make the Wozblaster work?
No it won’t work. ...
I built a Wozeblaster, but running with low volume and a lot of noise !!
Score: 162.22 %,
Type: Forum topic , Comments: 9 comments
I built a Wozblaster using Eric Boez design, but the volume is low and has a lot of noise (air shshing noise). Where should I start troubleshooting?
Assuming you hear a bit of Assuming you hear a bit of correct audio:
Normally you start ...
