Search results
CasLink2 has been updated. Also presentation slides are available.
Score: 110.56 %,
Type: Forum topic , Comments: 0 comments
their startup address outside the 0x4000-0x8000 range (for example: gberet.rom). Also a bug in command like ...
Cheap RGB to Video converter for vintage computers
Score: 129.85 %,
Type: Forum topic , Comments: 42 comments
Hello dear MSX fans,
The idea of creating a converter for connecting vintage computers to modern VGA monitors is not new. There are plenty of such projects on Internet. However, most of them are made for specific hardware, for example for Amiga. ...
SV 328 repair
Score: 128.63 %,
Type: Forum topic , Comments: 17 comments
anomalies on DOUT pin. On one chip the voltage is 1.4V, on 2 others 0.2V and on the rest - 0.07V. I presume ... (D7..D0) -> corresponding VDP pins -> Din/Dout of 4116 chip that's gone to heaven.
Tip2: ...
1024kb memory upgrade for Yamaha MSX2 YIS503
Score: 132.66 %,
Type: Forum topic , Comments: 51 comments
header connector has all the signals necessary for 128K (AD0-7 + CAS0/1), so in principle a replacement ... the extra “sub”-ROM with 80 columns support is in slot 3-0 and not slot 0-1 .
I was looking ... is in slot 3-0 and not slot 0-1 Smile.
I don't get it... Why is it a problem?
Well, assuming ...
F4 port board for MSX2+
Score: 129.72 %,
Type: Forum topic , Comments: 11 comments
computer? I assembled the F4 circuit on the FMPAC/F4 combo board, but I am still getting 255 (inverted 0 ...
Boards for Wozblaster revision 2 (Moonsound clone)
Score: 128.77 %,
Type: Forum topic , Comments: 1 comment
I made a batch of boards for Wozblaster revision 2 (Moonsound clone), 8 are available for a low price - 4 euro per board + 2 euro shipment within EU. Please contact me if you are interested. The Wozblaster on this board was assembled and tested already ...
MSX cartridge breadboards for prototyping
Score: 128.84 %,
Type: Forum topic , Comments: 2 comments
I made a batch of MSX cartridge breadboards for prototyping. Due to a stupid mistake most of the holes appeared to be smaller size than needed. The microchips in DIP casing can be easily installed onto the board but some components with thick pins ...
Game cartridge board for SV-328 and SVI-328
Score: 136.52 %,
Type: Forum topic , Comments: 14 comments
in the comments to the 'technical' files:
https://www.youtube.com/watch?v=K6Cj5Lw0QyE
Does ...
https://www.youtube.com/watch?v=K6Cj5Lw0QyE
Does it correspond to the boards shown in this thread?
Yes.
Sorry for digging up ...
C1: 0.1 (assuming uF). It's an 0805 surface mount part.
VD1: Is a LED.
The ASCII version ...
F4/FMPAC Light Combo Board project
Score: 141.82 %,
Type: Forum topic , Comments: 190 comments
inserted into MSX slots?
CS1 is not a problem, but SLTSEL wlll cause a conflict. If slot 0 ... the two digit versions.
Few typical examples:
Example 1:
/SLT0 (always reserved by BIOS)
/SLT1 ... shares same pin with extensions. This is possible because it uses logical /CS0 and therefore does ...
VRAM board for Yamaha CX5MII
Score: 131.46 %,
Type: Forum topic , Comments: 87 comments
connector pin is connected to the chip's A0 pin and AD0 connector pin is connected to the chip's ... of AD1, AD2 and AD0 on the connector is correct.
Anyway, I can share the schematics and gerber files, ... (except for AD7 and AD0 - on my board they are connected to A7 and A0 pins respectively).
Original ...
